Product Description
This listing is for a Heavy Duty Deep Transmission Pan with Step and Relief(for exhaust and cross-member clearance) and 2 Quarts Extra Capacity for vehicles that have the 65RFE, 66RFE and 68RFE Transmissions with a Black Powder Coat finish.It is designed specifically for trucks and SUVs with exhaust or cross member interference. Dimensions are provided in below in our Technical Information section, you should always check your vehicle for clearance before ordering a larger transmission pan. A magnetic drain plug and all mounting bolts are included with the pan. This pan has been designed for:
This pan has been installed in the following vehicles:
2014 and newer diesel trucks: Cooling tubes run under the stock transmission pan and this pan will not fit. Search PML part number 10304 in our store for a pan that could fit your vehicle. Jeep Owners: Check carefully. These Jeep vehicles most likely have this transmission do not have enough clearance for a larger transmission pan:
Dakota Owners and those with front routed exhaust: Other aftermarket pans have the step but not the curved relief for vehicles with the exhaust routed along the front of the pan. This pan has both. For a picture, see the installation on a Dakota below. Configurations vary so always check your vehicle. Please check your vehicle to be sure you have room for a larger pan (reference pan dimensions in our Technical Information section below). The exhaust system and frame cross members are the primary concerns. This pan is designed to work with the stock filter and gasket.PML designed this pan to work with the stock filter and gasket. For a gasket, PML recommends an inexpensive cork or cork composite type gasket or the silicon gasket maker. Some Dodge vehicles use the Mopar silicon gasket maker, which comes in a tube, with the stock pan. This works fine with a PML pan. There are two different stock pans and two different filters for this Chrysler/Dodge transmission. One is sometimes referred to as the "4WD filter" even though it is used on 2WD vehicles as well, it has a long pickup tube in the middle of the filter. The "2WD" filter is found on vehicles 2006-UP, the pickup tube is short and located near the end of the filter. For PML part numbers 10304 and 11039, you can use either filter. For PML part numbers 11078 and 11079, you must use the "4WD" filter. PML does not include a filter with the pan. Here is a list of filter part numbers that will work on all PML RFE pans:
The filter bolts onto the valve body, no filter support or extension is needed. The fluid will be at the same level with a stock pan as with the PML pan. The filter will pick up from the same place. PML designs pans and covers to work with stock parts without the need for additional modifications or complications. This pan comes with a LIMITED LIFETIME WARRANTY, for complete details please see our Warranty section below. WE ARE NOT RESPONSIBLE FOR YOU ORDERING A PART THAT DOES NOT FITYOUR VEHICLE. THE EBAY COMPATIBILITY CHART CANNOT BE TRUSTED TO BE 100% ACCURATE. Please seethe Technical Information/Identification Guide below for information on how to properly assure pan fitment. If you have questions or need assistance please contact us and we will do our best to assist you. As always, if you have any questions please feel free to message us here on eBay. We have an ASE certified transmission tech, with 25+ years experience rebuilding transmissions, available to answer your questions.
In the above photo you can see the interior of the pan and the cast-in baffles. These baffles are designed to direct oil to the filter inlet, keeping the oil near the pickup tube. These baffles also act as a heat sink to help with cooling and reduce sloshing. This pan has a location on the driver's side that can be machined for a temperature sending unit. The location is a circular boss and can accommodate between 1/8 NPT and 1/2 NPT. PML can drill and tap the hole to order for a $65 machining fee. In the above photo you can see a depth comparison between all of the available RFE PML pans. If one RFE pan will not fit there are 3 other options to choose from. ![]() Above you can see a side-by-side comparison of the Deep(11079)Pan with Step and Relief with the 2 stock pans.
|
PML products carry a lifetime limited manufacturer's warranty. Our products have proven to be trouble free since we began making them in 2000. If the pan or cover you receive is determined to have some kind of manufacturing defect (i.e., machining problem, leak due to porosity in pan wall), PML will replace the part. If you sell your vehicle with our part installed, we will honor the warranty with the new owner. If you run a cover or pan into a boulder and it cracks or is damaged, well, there's nothing PML can help you with there. Modifying our products voids the warranty. Our products are designed to fit factory original equipment. However, in some applications, or because of the use of certain factory options and/or after market equipment, there may be clearance or fitment problems between our products and your vehicle components. PML provides dimensions and pictures so you can check your vehicle before ordering. It is the responsibility of the vehicle owner and installer to install the part correctly and to ensure that there is no contact between the PML part and other moving or fixed vehicle components. World Wide Specialty Parts and PML assumes no liability, expressed or implied, for damage or injury to persons or property. This warranty does not cover: Removal and Replacement Labor Costs, Loss of time, Inconvenience or other Consequential Damage. |